2 thoughts on “What are the common diamond inlaid methods”
Penny
The common eight major diamond inlaid claws are inlaid The long metal claws (columns) tightly hold diamonds. It is currently becoming a popular single diamond decoration style in the market. Claw sets can generally be divided into six claws, four -claws, and three -claws. Nowadays, the six -claw crown is popular in wedding diamond rings. The princess's diamond can use four -claw inlaid. In order to be firm, the large -grained diamonds sometimes use two small claws to form one claw. advantages: is that the metal rarely blocks the diamond, clearly presents the beauty of the diamond, and facilitates the light into and reflects at different angles, making the diamond look bigger and brighter. Disadvantages: The claws are easy to hang on hair or fabrics. If it is platinum, because it is soft, it may cause deformation of the claws and diamond falling off.
The pack of inlaid This Using the metal side, the diamond waist is sealed within the metal trash (frame), and the diamond is used to prevent the diamond from falling off with the solids of the precious metal. This is the most firm and traditional inlaid method. It shows the light of diamonds, light and restrained, and has a peaceful and dignified temperament. When buying a packet inlaid diamond, carefully observe that the tip of the diamond cannot expose the bracket, otherwise it will damage the skin or hit the diamond. advantages: The protection of diamonds, especially for the pavilion and waist of the diamond, making the surface of the ring smoother and more fixed to diamonds. Disadvantages: The metal required, cumbersome processing, high cost, and relatively small light entering the diamond, making the beauty of diamonds be fully reflected. It is more suitable for older women to wear or male ring. Inlaid.
The card inlaid The waist or waist and waist and bottom tip of the diamond with the tension of the metal, which is a more trendy style nowadays. The popular card inlaid and V -folding inlaid now belong to this category. In short, it is to open a shallow slot on both sides of the metal. Inlaid further, sparkling glory. Disadvantages: The position of the gemstone is limited by metal, and the force point is very small. If the slot car is too large, it is easy to cause diamond loosening or even falling off, so inlay in this way It is required to be higher than claw setting.
This inlaid is a method of getting the groove on the precious metal bracket, and then the diamond is clamped into the groove. The orbital inlaid method is suitable for diamonds with the same caliber. One by one is inlaid in the metal orbit one by one, and the diamonds are supported by both sides of the metal. It is used to inlaid round, narrow square and square gemstone. The groove is like a railway with diamonds in the middle. : This inlaid method can make the surface of the decoration look smooth. It is a relatively secure way. The ring is full of small diamonds. This inlay is commonly used. It has good protection for the waist of the diamond. It can give people a neat and smooth feeling visually. Disadvantages: The diamond ring inlaid is not suitable for changing the size of the hand circle. Once the metal's arc changes change, it is easy to cause the diamond to fall off. Therefore Because the diamond ring of the slot is similar to the mode of inlaid diamond in the middle of a rail, so that the diamonds in the middle are often not as firm as the claw inlaid.
The jeep inlaid is also called inlaid and hidden inlaid. Diamonds are often inlaid with a jeeping method for the ring. This style is very popular nowadays. This style is more popular in men's rings. This style of diamond ring first inlaid the diamond can be better wrapped in the hole in the diamond waist, and then the surrounding metal is fixed to fix the diamond. advantages: This can better protect the diamond waist. If it is inlaid, the diamond will be more stable and the appearance is more beautiful and generous. Disadvantages: This is very consumed. When inlaid, it is easy to cause damage to diamonds. The return material for pressing the diamond is often narrow and the diamond is very easy to fall off.
The nail inlaid The edge of the mouth inlaid on the metal material, use a tool to shovel a few small nails to fix the diamond. Based on the number of nail nails, the number of nails is divided into two nails, three nails inlaid, four nails and dense nails. R n Advanced: The metal or paws that do not see any fixed diamond on the surface. The tightly arranged diamonds are actually covered in the metal mortise. Because there is no metal surround, diamonds can penetrate and reflect more sufficient light, highlighting the gorgeous light of diamond jewelry. Disadvantages: It is not suitable for a single diamond inlaid. If it is used in large areas, it is not suitable for changing the rings.
This inlaid does not use the tooth mouth to punch the metal directly on the metal. Drinks in the cars, embed the diamond, and then wrap the surrounding metal. The metal ring has the effect of diamond enlarging visually. This inlaying method is very difficult. The diamond countertop and the surrounding metals are on the same plane. It also requires that the metal support must have a certain thickness, which can bury the diamond inside, and the bottom tip of the pavilion cannot be exposed. The inlaid jewelry in this way looks stable and generous, and many small diamonds on the ring on the ring adopt this inlay. advantages: This method is very comfortable to wear, saves metal, diamonds are safer, not easy to hook or easy to touch. Disadvantages: The diamond buried in the precepts, which is the same as the surface of the precepts. Diamonds will be covered out.
The row inlaid This style is to be inlaid densely by rowing diamonds. Diamonds are inlaid in various holes in the ring, so that the diamond and ring are almost on the same plane. Used for women's rings. advantages: can better protect diamonds than claws. In addition, this style makes most of the diamond exposure, which can produce a larger or more visual effect than the actual or more diamond. Disadvantages: This inlaid is often dangerous, because diamonds are easily damaged during the inlaid process. The degree of diamond fixing is not as good as other styles. Diamond inlaid process is suitable for small score diamonds.
The diamond to wear diamond rings, choose big ones! Most flashing! Cut 3EX! But have you noticed this little problem. What method does your beloved diamond ring inlaid? The choice of inlaid method is often overlooked, but it has the importance to the glorious image and safety index of the gemstone, and the Luohua jewelry will explain them one by one.
1. Claw inlaid The long precious metal inlaid claws "grab" diamonds. Common types of types are four -claws and six claws. However, the claw set still requires strictness. The size of the claws is consistent, the interval is uniform, and the diamond countertop level is not tilted. The two gems in the picture are steadily located on the metal claws, which is very firm to ensure that the gem is not easy to fall. It can make the diamond more prominent, and the light is shot from all directions. Its dazzling luster is very bright from all angles. The claws inlaid diamond ring are simple in shape and are very unavailable. Girls of various hand shapes can be worn with confidence. However, it should be noted whether the metal claws and diamond binding are hidden in dirt. Every 6-12 months need to be delivered to the corresponding jewelry shop for maintenance to prevent the twisted and fracture of claws cause losses of love diamonds.
2. Bags inlaid The diamond ring that likes more firmly like this type of diamond ring. You must be interested in it. Wrap the diamond waist with metal thin slices as a metal. Inside. There is no gap between the inlaid gemstone and the edges, the edges should be evenly smooth, the ditch is smooth and smooth, and there is no place to touch the hand. The traditional style and more subtle and stable design will choose to inlay this method, which is very atmospheric. However, if you are maintained, you must pay attention. If the bag is firm, cleaning naturally becomes a big project. If you do n’t have that confidence, please send it to the corresponding person. In addition, although the packet is inlaid insurance, the maintenance cannot be relaxed. See if the metal bag is raised and deformed regularly, it will help protect the long -lasting glory of the diamond ring shining.
3. Second of the inset The metal material used to inlaid gemstones, the edge of the inlaid mouth, shovel several small nails to fix diamonds, at least 7 and more small gems need This technique will be used in group inlaid. Those small diamonds who cannot achieve a diamond jewelry are saved through this high -energy technique, and their group arrangement effects are really not ordinary. Fully proved that "the unity power is great."
Okay, I want to move bricks, and I write here for a while. The following chapters will introduce the various necklaces and pendants of Luohua Jewelery, as well as brand and interesting design, it will be
The common eight major diamond inlaid claws are inlaid
The long metal claws (columns) tightly hold diamonds. It is currently becoming a popular single diamond decoration style in the market. Claw sets can generally be divided into six claws, four -claws, and three -claws. Nowadays, the six -claw crown is popular in wedding diamond rings. The princess's diamond can use four -claw inlaid. In order to be firm, the large -grained diamonds sometimes use two small claws to form one claw.
advantages:
is that the metal rarely blocks the diamond, clearly presents the beauty of the diamond, and facilitates the light into and reflects at different angles, making the diamond look bigger and brighter.
Disadvantages:
The claws are easy to hang on hair or fabrics. If it is platinum, because it is soft, it may cause deformation of the claws and diamond falling off.
The pack of inlaid
This Using the metal side, the diamond waist is sealed within the metal trash (frame), and the diamond is used to prevent the diamond from falling off with the solids of the precious metal. This is the most firm and traditional inlaid method. It shows the light of diamonds, light and restrained, and has a peaceful and dignified temperament. When buying a packet inlaid diamond, carefully observe that the tip of the diamond cannot expose the bracket, otherwise it will damage the skin or hit the diamond.
advantages:
The protection of diamonds, especially for the pavilion and waist of the diamond, making the surface of the ring smoother and more fixed to diamonds.
Disadvantages:
The metal required, cumbersome processing, high cost, and relatively small light entering the diamond, making the beauty of diamonds be fully reflected. It is more suitable for older women to wear or male ring. Inlaid.
The card inlaid
The waist or waist and waist and bottom tip of the diamond with the tension of the metal, which is a more trendy style nowadays. The popular card inlaid and V -folding inlaid now belong to this category. In short, it is to open a shallow slot on both sides of the metal. Inlaid further, sparkling glory.
Disadvantages:
The position of the gemstone is limited by metal, and the force point is very small. If the slot car is too large, it is easy to cause diamond loosening or even falling off, so inlay in this way It is required to be higher than claw setting.
This inlaid
is a method of getting the groove on the precious metal bracket, and then the diamond is clamped into the groove. The orbital inlaid method is suitable for diamonds with the same caliber. One by one is inlaid in the metal orbit one by one, and the diamonds are supported by both sides of the metal. It is used to inlaid round, narrow square and square gemstone. The groove is like a railway with diamonds in the middle.
:
This inlaid method can make the surface of the decoration look smooth. It is a relatively secure way. The ring is full of small diamonds. This inlay is commonly used. It has good protection for the waist of the diamond. It can give people a neat and smooth feeling visually.
Disadvantages:
The diamond ring inlaid is not suitable for changing the size of the hand circle. Once the metal's arc changes change, it is easy to cause the diamond to fall off. Therefore Because the diamond ring of the slot is similar to the mode of inlaid diamond in the middle of a rail, so that the diamonds in the middle are often not as firm as the claw inlaid.
The jeep inlaid
is also called inlaid and hidden inlaid. Diamonds are often inlaid with a jeeping method for the ring. This style is very popular nowadays. This style is more popular in men's rings. This style of diamond ring first inlaid the diamond can be better wrapped in the hole in the diamond waist, and then the surrounding metal is fixed to fix the diamond.
advantages:
This can better protect the diamond waist. If it is inlaid, the diamond will be more stable and the appearance is more beautiful and generous.
Disadvantages:
This is very consumed. When inlaid, it is easy to cause damage to diamonds. The return material for pressing the diamond is often narrow and the diamond is very easy to fall off.
The nail inlaid
The edge of the mouth inlaid on the metal material, use a tool to shovel a few small nails to fix the diamond. Based on the number of nail nails, the number of nails is divided into two nails, three nails inlaid, four nails and dense nails. R n Advanced:
The metal or paws that do not see any fixed diamond on the surface. The tightly arranged diamonds are actually covered in the metal mortise. Because there is no metal surround, diamonds can penetrate and reflect more sufficient light, highlighting the gorgeous light of diamond jewelry.
Disadvantages:
It is not suitable for a single diamond inlaid. If it is used in large areas, it is not suitable for changing the rings.
This inlaid
does not use the tooth mouth to punch the metal directly on the metal. Drinks in the cars, embed the diamond, and then wrap the surrounding metal. The metal ring has the effect of diamond enlarging visually. This inlaying method is very difficult. The diamond countertop and the surrounding metals are on the same plane. It also requires that the metal support must have a certain thickness, which can bury the diamond inside, and the bottom tip of the pavilion cannot be exposed. The inlaid jewelry in this way looks stable and generous, and many small diamonds on the ring on the ring adopt this inlay.
advantages:
This method is very comfortable to wear, saves metal, diamonds are safer, not easy to hook or easy to touch.
Disadvantages:
The diamond buried in the precepts, which is the same as the surface of the precepts. Diamonds will be covered out.
The row inlaid
This style is to be inlaid densely by rowing diamonds. Diamonds are inlaid in various holes in the ring, so that the diamond and ring are almost on the same plane. Used for women's rings.
advantages:
can better protect diamonds than claws. In addition, this style makes most of the diamond exposure, which can produce a larger or more visual effect than the actual or more diamond.
Disadvantages:
This inlaid is often dangerous, because diamonds are easily damaged during the inlaid process. The degree of diamond fixing is not as good as other styles. Diamond inlaid process is suitable for small score diamonds.
There are several inlaying methods of jewelry
The diamond to wear diamond rings, choose big ones! Most flashing! Cut 3EX! But have you noticed this little problem. What method does your beloved diamond ring inlaid? The choice of inlaid method is often overlooked, but it has the importance to the glorious image and safety index of the gemstone, and the Luohua jewelry will explain them one by one.
1. Claw inlaid
The long precious metal inlaid claws "grab" diamonds. Common types of types are four -claws and six claws. However, the claw set still requires strictness. The size of the claws is consistent, the interval is uniform, and the diamond countertop level is not tilted. The two gems in the picture are steadily located on the metal claws, which is very firm to ensure that the gem is not easy to fall. It can make the diamond more prominent, and the light is shot from all directions. Its dazzling luster is very bright from all angles. The claws inlaid diamond ring are simple in shape and are very unavailable. Girls of various hand shapes can be worn with confidence. However, it should be noted whether the metal claws and diamond binding are hidden in dirt. Every 6-12 months need to be delivered to the corresponding jewelry shop for maintenance to prevent the twisted and fracture of claws cause losses of love diamonds.
2. Bags inlaid
The diamond ring that likes more firmly like this type of diamond ring. You must be interested in it. Wrap the diamond waist with metal thin slices as a metal. Inside. There is no gap between the inlaid gemstone and the edges, the edges should be evenly smooth, the ditch is smooth and smooth, and there is no place to touch the hand. The traditional style and more subtle and stable design will choose to inlay this method, which is very atmospheric. However, if you are maintained, you must pay attention. If the bag is firm, cleaning naturally becomes a big project. If you do n’t have that confidence, please send it to the corresponding person.
In addition, although the packet is inlaid insurance, the maintenance cannot be relaxed. See if the metal bag is raised and deformed regularly, it will help protect the long -lasting glory of the diamond ring shining.
3. Second of the inset
The metal material used to inlaid gemstones, the edge of the inlaid mouth, shovel several small nails to fix diamonds, at least 7 and more small gems need This technique will be used in group inlaid. Those small diamonds who cannot achieve a diamond jewelry are saved through this high -energy technique, and their group arrangement effects are really not ordinary. Fully proved that "the unity power is great."
Okay, I want to move bricks, and I write here for a while. The following chapters will introduce the various necklaces and pendants of Luohua Jewelery, as well as brand and interesting design, it will be